zuloosharing.blogg.se

1. ALLEN DATAGRAPH I536 GTS DRIVERS FULL
2. ALLEN DATAGRAPH I536 GTS DRIVERS SOFTWARE
3. ALLEN DATAGRAPH I536 GTS DRIVERS PROFESSIONAL
4. ALLEN DATAGRAPH I536 GTS DRIVERS WINDOWS

The 230/315 offers four coordinate systems for widespread compatibility with CAS (Computer Aided Sign making) software programs. The knobs have a CAS (Computer Aided Signmaking) position which allows the 200 Series's Speed and Force to be controlled remotely by your Signmaking software, provided that speed and force settings are available. The 230/315 has front panel control knobs for speed and force.

ALLEN DATAGRAPH I536 GTS DRIVERS WINDOWS

Set-Ups are accessed through the Windows Control Panel under the SETTINGS menu. S ET-U P 1, which is the power up default, can be set for the most often used configuration. Control settings on the cutter are saved in a S ET-U P and then recalled for simple control of machine parameters. The 230 has three programmable S ET-U Ps which can be customized for convenient use of a variety of software, material and tool combinations. The Allen Remote Panel provides access to the machine's controls and diagnostics. The 230/315 has extensive built-in self test capability to assure continuously high quality output. The 230/315 use a modular design to provide rapid fault diagnosis and component replacement, which insures minimum downtime and replacement cost. The service loop feature may be activated in the Allen Remote Panel if so desired. This loop allows higher speed cutting than can normally be attained on drum type plotters. The 230/315 can maintain a service loop of material so that the cutter does not pull off the supply roll during cutting. Material can not be pulled off a large supply roll accurately at this speed. The 230/315 Vinyl Cutter is capable of a top speed of 24 in/sec (60 cm/s). The Model 315 is a fixed width cutter and accepts only 15 inch punched material. For use without the optional guide system, it is suggested that the frame size be limited to 10 feet (3 m). The frame length on roll media is not limited by software in the plotter. Sensing the magnets located in the right and left pinch wheel brackets and will not attempt to move beyond this width. The 230 automatically detects material width during the Load cycle by The 230 will handle sheets or rolls of material in widths from 3.5 inches (90 The The Model 230 accepts material from 3.5" (88.9mm) to 30 inches (762 mm) in width.

These modes may be activated by HPGL command in the sign making software or from the Allen Remote Panel program.Ī wide variety of vinyls, films, papers, stencil, sandblast mask and banner materials can be handled by the 230 for cutting, drawing, plotting and banner making. The 230/315 Vinyl Cutter has two modes of operation: Cut and Draw. High has a top force of 550 grams, and is used when cutting heavier materials such as sandblast mask, magnetic sheeting, etc. Low is sufficient for most vinyl cutting applications, and has a top cutting pressure of 250 grams at 100% on the cutter's force dial. The two modes are listed as FORCE POT RANGE, high and low. These modes are contained in the OPTIONS menu under SETUP in the remote panel program. There are 2 modes to the force adjustment, which can be accessed through the Windows remote panel provided with the cutter. The Model 230 features Allen's exclusive Gold Touch Cutting head, which allows the user up to 550 grams of cutting pressure.

ALLEN DATAGRAPH I536 GTS DRIVERS FULL

The Allen Remote Panel program provides direct user control of speed, force and position, as well as having a full gamut of diagnostics. The 230/315 uses HPGL command language for widespread compatibility and emulates the Roland CAMM-1, the Hewlett Packard 758x, and DMPL plotters. Most of the operational procedures are the same for both the 230 and 315 cutters, with the exception of the differences relating to the material transport method, and the ability of the 315 to produce pounce patterns with the optional pounce kit available from Allen Datagraph Systems.Ī Model 315 addendum appears at the end of this manual, which outlines the different operational procedures relating specifically to the 315.Ī thumb screw tool holder allows tools to be quickly and easily changed. The Model 315 utilizes precision sprocket assemblies which accept the standard IBM compatible punch pattern as well as "universal punch" vinyls and Gerber 15" punched vinyl. The 230 utilizes a precision grit wheel system for positive tracking and movable pinch wheels for handling punched or unpunched materials in standard and nonstandard sizes. The 230/315 cuts with a swivel knife or draws with various pens and markers.

ALLEN DATAGRAPH I536 GTS DRIVERS PROFESSIONAL

The Allen Datagraph Systems Model 230 and 315 Vinyl Cutters are high performance machines designed for the graphics professional to cut and draw on a wide variety of materials.